Frameless and torque motors

What frameless and torque motors are

A frameless motor is a brushless motor without the parts that make it a stand-alone product. You get a wound stator and a magnet rotor. The housing, shaft, bearings, feedback and cooling are yours. The stator is bonded or clamped into a bore in your structure, and the rotor goes onto the shaft you are driving.

That is the point of them. Removing the motor’s own housing, bearings and coupling shortens the axis, saves mass and puts the torque directly where it is needed. Kollmorgen notes that a direct-drive axis has no mechanical compliance, backlash or lost motion between motor and load (Kollmorgen). Large-diameter kits usually leave a big through-bore for cables, slip rings, optics or a coaxial brake.

Typical uses are robot and cobot joints, gimbals and stabilised platforms, rotary and index tables, medical devices, semiconductor stages and spindle-like axes. Bus voltages run from 48 VDC or less up to around 680 VDC, and continuous torque from fractions of a newton metre to several thousand.

Types compared

Type	What you get	Best for	Trade-offs
Frameless kit (slotted)	Rotor and stator only	Robot joints, compact axes, highest torque per mass	You design bearings, housing, cooling and feedback
Frameless kit (slotless/ironless)	Rotor and stator, no cogging	Gimbals, optics, metrology, very smooth low speed	Lower torque density
Housed direct-drive (torque) motor	Complete motor with bearings and encoder	Rotary tables and indexers without gearing	Larger and heavier than a kit
Linear motor (iron-core or ironless)	Forcer and magnet track	Direct-drive linear stages, gantries	Open magnet track, needs linear encoder and guides
Gear-integrated actuator	Motor, strain-wave gear and encoder in one unit	Joints and positioners where integration time matters	Gear compliance and lost motion return

Frameless kits

Kits are offered by diameter and stack length, in several windings for different bus voltages. Akribis ADR-F covers small 48 VDC kits for compact joints; Akribis ADR-P covers larger high-voltage kits with big through-bores.

Housed direct-drive motors

Housed torque motors bring their own bearing and encoder and bolt straight to a table or fixture. Examples include Akribis AXD, the absolute-encoder AXD-ERA, and the ironless, zero-cogging ACD for very smooth low-speed motion.

Linear motors, briefly

The linear equivalent is a forcer moving over a magnet track. Iron-core types such as Akribis AKM give high force; ironless U-channel types such as Akribis AUM remove cogging for smooth scanning. Tubular motors such as LinMot P10-54 package the magnets inside a sealed rod.

Gear-integrated actuators

Where a joint needs a ratio, motor and strain-wave gear can be bought as one unit, for example the hollow-shaft Harmonic Drive FHA-C. This saves integration time at the cost of design freedom.

Frameless vs housed vs geared: when to use which

• Frameless kit when axial length, mass and through-bore drive the design, and you have the mechanical and thermal engineering capacity to integrate it.
• Housed direct drive when you want gearless stiffness and accuracy on a table or indexer without designing bearings and encoder mounts.
• Frameless plus strain-wave gear for most robot joints, where torque per kilogram matters and a small amount of gear compliance is acceptable. A 100:1 gear reduces reflected load inertia by 10,000 times.
• Housed servo plus gearbox when cost and lead time beat integration. See servo and stepper motors and gearboxes.

How to size a frameless motor

1. Torque and speed at the joint

Work out the peak and RMS torque from the move profile, payload, arm or table inertia and gravity. If the joint is geared, divide by the ratio and efficiency to get motor torque, and multiply speed by the ratio.

2. Use the motor constant

The motor constant Km = Kt / √R (Nm/√W) tells you how much torque you get per watt of heat. Allient notes that Km rises faster with diameter than with length, so the largest diameter and shortest stack that meets the Km target is usually the most efficient choice (Allient). Copper loss at a given torque is (T / Km)². Datasheets do not always quote Km; you can calculate it from Kt and resistance.

3. Model the thermal path

This is the step that catches most designs out. Kollmorgen’s TBM ratings, for instance, assume 25 °C ambient and a specified heat sink, with hot parameters quoted at a 155 °C winding temperature (Kollmorgen TBM guide). Your housing may be smaller, enclosed or near other heat sources. Kollmorgen recommends steel or aluminium housings with at least 4–6 mm wall thickness and warns that stainless steel conducts heat poorly. Allient adds that a power-off brake adds heat while the joint is moving. Build a thermal model per joint and expect to derate.

Also consider what the heat reaches. A winding running near its limit can damage bearing grease, gear lubricant and encoder electronics nearby.

4. Choose feedback and temperature sensing

Absolute encoders give commutation and position at power-up, removing separate Hall sensors; Kollmorgen suggests 18-bit or higher for high-repeatability axes, with resolvers (typically 12–16 bits) for high shock. In geared joints, Allient and TQ both describe a second encoder on the output to measure true joint position. For temperature, a linear sensor such as a PT1000 helps characterise the motor during prototyping; a PTC gives a simple trip.

5. Cogging and smoothness

Slotted designs give the most torque but have some cogging. Kollmorgen’s TBM data quotes peak-to-peak cogging per model, from about 0.01 Nm on small frames to around 0.3 Nm on the largest. For gimbals and scanning optics, choose slotless or ironless designs, or ask for cogging data and compensation options. Allient notes that higher-frequency cogging is generally easier to tune out than low-frequency cogging.

Integration and common mistakes

• Trusting datasheet continuous torque. It is only valid for the test heat sink and ambient.
• Stainless or thin housings. These trap heat; increase wall section or use aluminium.
• Poor concentricity. Follow the manufacturer’s tolerances for rotor and stator alignment; an uneven air gap causes torque ripple and unbalanced magnetic pull.
• Unsafe assembly. Rotor magnets pull hard on the stator and on steel tools. Plan fixtures for insertion.
• Bearings sized for the motor, not the load. The machine’s bearings carry everything, and should be serviceable if radial loads are high.
• No brake plan. Fit the brake on the primary driven shaft and include its heat in the budget.
• Encoder mounted on a compliant path. Mount it rigidly to the rotor or output it measures.

For robot joints in particular, the frameless motor sizing guide for robot joints works through a full example, and robotics and cobots covers the wider system.

What to send an engineer for a quote

• Peak and RMS torque, maximum speed, and the move profile
• Available envelope: maximum OD, minimum ID (through-bore), axial length
• Bus voltage and drive current limits
• Housing material, wall section, ambient temperature and any cooling
• Feedback type and resolution, and whether you need an output-side encoder
• Gear ratio and type if geared
• Brake, smoothness or cogging limits, and any vacuum, cleanroom or radiation requirements
• Expected volumes, since custom windings and stack lengths are often possible

Send these through the spec builder below and our specialist engineering and supply partners will shortlist kits or housed units to suit.

Guides

Where frameless and torque motors are used

What we need to know to specify frameless and torque motors

These are the questions an applications engineer works through first. Approximate answers are fine: ranges narrow the options quickly, and we confirm the details with you.

• Outer diameter: Under 50 mm, 50–100 mm, 100–200 mm, Over 200 mm
• Peak torque: Under 2 Nm, 2–20 Nm, 20–200 Nm, Over 200 Nm
• Use: Robot joint, Gimbal / pan-tilt, Rotary table, Spindle
• Hollow shaft: Yes, No

We also ask about the environment (washdown, outdoor, subsea, ATEX, vacuum, shock and EMC), annual quantities and timescale, because these decide whether a standard, modified or custom design is the best fit.

39 series compared

Series from 18 manufacturers, grouped by type. Figures are the highest published for each series. Open a series for the full specification and, for brands outside our supply network, the alternatives that meet or exceed it.

Frameless torque motor (25)

Housed direct-drive motor (14)

Summarised from manufacturers' published data. Always confirm against the current datasheet; an engineer will check the fit before recommending anything.

Brands