AC servo motor
Control Techniques Unimotor hd servo motors
Low-inertia servo motors in frames 060 to 190 with rated torque from 0.64 to 85 Nm and 255 Nm peak, rated speeds from 1,000 to 6,000 rpm and IP65, matched to Digitax HD and Unidrive M70x.
Key specifications
| Ingress protection | IP65 |
|---|---|
| Rated torque | 0.64–85 Nm |
| Peak torque (max) | 255 Nm |
| Rated speed | 1,000–6,000 |
| Supply | 220 V and 400 V windings |
| Feedback | resolver, incremental, inductive absolute, SinCos/absolute; EnDat 2.1/2.2/3; SIL 3 encoder option |
| Sizes | 060, 067, 089, 115, 142, 190 |
Summarised in our own words from Nidec Corporation's published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Specify Motion is not affiliated with Nidec Corporation. Control Techniques and Unimotor hd servo motors are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Typical applications
Alternatives that meet or exceed these figures
Engineers often come to us with a Control Techniques part number and leave with an alternative that is easier to source, quicker to deliver or a better fit for the machine. These series from our supply network is the closest match on published figures.
Leadshine's AC servo motors for the EL8/EL7/EL6 drives: ELM1 is the economy line and ELM2 the general-purpose line, both with 23-bit absolute encoders, IP65/IP67 sealing and up to 3.5x overload. The catalogue extends ELM2M to 22 kW and previews a 26-bit ELM3.
View ELM1 / ELM2 AC Servo Motors →Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
What an AC servo motor is
An AC servo motor is a permanent-magnet synchronous motor designed for closed-loop control of position, speed and torque. A wound stator is driven by a servo drive with sinusoidal three-phase current, while magnets on the rotor follow the rotating field. A high-resolution encoder or resolver on the shaft feeds position back to the drive, which adjusts current many thousands of times a second. The result is precise, dynamic motion with high peak torque, typically about three times the continuous rating for short periods.
When engineers choose an AC servo motor
Choose an AC servo for machine axes needing fast, accurate motion under varying loads, such as packaging, robotics, machine tools and printing. Compared with steppers, servos keep torque at high speed and cannot silently lose position. The trade-offs are cost and set-up: a servo needs a matched drive, feedback and tuning. For simple, low-speed indexing with a steady load, a stepper may be cheaper. For very low speeds and high torque, a gearbox or direct-drive motor may be needed.
How to specify the Control Techniques Unimotor hd servo motors
Send these with your enquiry and an engineer can confirm the right Unimotor hd servo motors variant or an equivalent:
- Continuous and peak torque (Nm)
- Rated and maximum speed (rpm)
- Load inertia and inertia ratio
- Supply voltage: 230 V single-phase or 400 V three-phase
- Feedback: incremental or absolute encoder, resolution (bits)
- Holding brake, IP code and shaft options
- Flange size and mounting (mm)
Common mistakes to avoid
- Sizing on peak torque without checking RMS torque over the cycle
- Ignoring load-to-motor inertia ratio, which makes tuning hard
- Forgetting the brake is for holding, not dynamic stopping
- Using a motor and drive pair that the supplier has not matched
Control Techniques Unimotor hd servo motors: frequently asked questions
What is the Control Techniques Unimotor hd servo motors?
Low-inertia servo motors in frames 060 to 190 with rated torque from 0.64 to 85 Nm and 255 Nm peak, rated speeds from 1,000 to 6,000 rpm and IP65, matched to Digitax HD and Unidrive M70x. Published series figures include rated torque 0.64 Nm, rated torque 85 Nm, peak torque 255 Nm. It is made by Nidec Corporation; Specify Motion can help source it or propose an equivalent.
Who makes the Control Techniques Unimotor hd servo motors?
The Control Techniques Unimotor hd servo motors is made by Control Techniques (Nidec Corporation) and is listed here for engineers comparing options. Specify Motion is not affiliated with Nidec Corporation; brand names are used only to identify the product.
What is the rated torque of the Control Techniques Unimotor hd servo motors?
The published series minimum rated torque is 0.64 Nm. Individual models and sizes in the Unimotor hd servo motors range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Control Techniques Unimotor hd servo motors?
Yes. On published figures, Leadshine ELM1 / ELM2 AC Servo Motors is the closest match from our supply network. An engineer confirms the fit against your application before recommending anything.
What is the inertia ratio in servo sizing?
The inertia ratio compares the load inertia reflected to the motor shaft with the motor's rotor inertia. High ratios make the axis harder to tune and slower to settle. Many engineers aim for below about 10:1, and lower for highly dynamic axes, using a gearbox to reduce reflected inertia where needed.
Do AC servo motors need an absolute encoder?
Not always. Incremental encoders need a homing routine after power-up, which is acceptable on many machines. Absolute encoders know their position at power-on, avoiding homing, which saves time and suits robots and multi-axis machines. Multi-turn absolute encoders track turns even when power is off.
Further reading: How to select a servo motor · Servo vs stepper · Servo and stepper motors
Other ac servo motor series
Spec builder
Specify what you need instead of Unimotor hd servo motors
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Control Techniques Unimotor hd servo motors: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.