AC servo motor
Delta Electronics ECM-B3 servo motors
AC servo motors for ASDA-B3 from about 0.1 to 7.5 kW, rated torque 0.32 to 47.75 Nm and peak torque up to 119 Nm, up to 6,000 rpm on 3,000 rpm models, with 24-bit optical or 17-bit magnetic encoders.
Key specifications
| Ingress protection | IP67 with waterproof connectors and shaft/oil seal |
|---|---|
| Rated torque | 0.32–47.75 Nm |
| Peak torque (max) | 119 Nm |
| Speed (max) | 6,000 rpm |
| Power | 100–7,500 W |
| Feedback | 24-bit optical or 17-bit magnetic, absolute or incremental |
| Resolution (max) | 24 bit |
Summarised in our own words from Delta Electronics, Inc.'s published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Figures from the ASDA-B3 catalogue (Traditional Chinese edition).
Specify Motion is not affiliated with Delta Electronics, Inc.. Delta Electronics and ECM-B3 servo motors are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Typical applications
Alternatives that meet or exceed these figures
Engineers often come to us with a Delta Electronics part number and leave with an alternative that is easier to source, quicker to deliver or a better fit for the machine. These 3 series from our supply network are the closest match on published figures.
Kinco's current-generation AC servo motor line, matched to the JD2 and FD5P PRO drives. Small-inertia 40-80 mm frames run at 3000 rpm on 220 V; large-inertia 130 and 180 mm frames are 1500 rpm machines reaching 47.8 Nm rated and 7.5 kW, with 23-bit multi-turn absolute encoders as standard.
| Published maximum | ECM-B3 servo motors | SMK Series AC Servo Motors (SMK40S/60S… |
|---|---|---|
| Rated torque | 47.75 Nm | 47.8 Nm meets or exceeds |
| Peak torque | 119 Nm | 119.5 Nm meets or exceeds |
| Speed | 6,000 rpm | 6,000 rpm meets or exceeds |
| Power | 7,500 W | 7,500 W meets or exceeds |
Kinco's established AC servo motor range from 40 to 180 mm frames, covering 50 W to 7.5 kW and up to 48 Nm rated torque. Standard feedback is a 2500-line incremental encoder with Hall commutation, with absolute options and a resolver on the 180 mm frame. Pairs with FD2S and CD2S drives.
| Published maximum | ECM-B3 servo motors | SMH Series AC Servo Motors (SMH40S-SMH… |
|---|---|---|
| Rated torque | 47.75 Nm | 48 Nm meets or exceeds |
| Peak torque | 119 Nm | — |
| Speed | 6,000 rpm | — |
| Power | 7,500 W | 7,500 W meets or exceeds |
Leadshine's AC servo motors for the EL8/EL7/EL6 drives: ELM1 is the economy line and ELM2 the general-purpose line, both with 23-bit absolute encoders, IP65/IP67 sealing and up to 3.5x overload. The catalogue extends ELM2M to 22 kW and previews a 26-bit ELM3.
| Published maximum | ECM-B3 servo motors | ELM1 / ELM2 AC Servo Motors |
|---|---|---|
| Rated torque | 47.75 Nm | — |
| Peak torque | 119 Nm | — |
| Speed | 6,000 rpm | — |
| Power | 7,500 W | 7,500 W meets or exceeds |
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
What an AC servo motor is
An AC servo motor is a permanent-magnet synchronous motor designed for closed-loop control of position, speed and torque. A wound stator is driven by a servo drive with sinusoidal three-phase current, while magnets on the rotor follow the rotating field. A high-resolution encoder or resolver on the shaft feeds position back to the drive, which adjusts current many thousands of times a second. The result is precise, dynamic motion with high peak torque, typically about three times the continuous rating for short periods.
When engineers choose an AC servo motor
Choose an AC servo for machine axes needing fast, accurate motion under varying loads, such as packaging, robotics, machine tools and printing. Compared with steppers, servos keep torque at high speed and cannot silently lose position. The trade-offs are cost and set-up: a servo needs a matched drive, feedback and tuning. For simple, low-speed indexing with a steady load, a stepper may be cheaper. For very low speeds and high torque, a gearbox or direct-drive motor may be needed.
How to specify the Delta Electronics ECM-B3 servo motors
Send these with your enquiry and an engineer can confirm the right ECM-B3 servo motors variant or an equivalent:
- Continuous and peak torque (Nm)
- Rated and maximum speed (rpm)
- Load inertia and inertia ratio
- Supply voltage: 230 V single-phase or 400 V three-phase
- Feedback: incremental or absolute encoder, resolution (bits)
- Holding brake, IP code and shaft options
- Flange size and mounting (mm)
Common mistakes to avoid
- Sizing on peak torque without checking RMS torque over the cycle
- Ignoring load-to-motor inertia ratio, which makes tuning hard
- Forgetting the brake is for holding, not dynamic stopping
- Using a motor and drive pair that the supplier has not matched
Delta Electronics ECM-B3 servo motors: frequently asked questions
What is the Delta Electronics ECM-B3 servo motors?
AC servo motors for ASDA-B3 from about 0.1 to 7.5 kW, rated torque 0.32 to 47.75 Nm and peak torque up to 119 Nm, up to 6,000 rpm on 3,000 rpm models, with 24-bit optical or 17-bit magnetic encoders. Published series figures include rated torque 0.32 Nm, rated torque 47.75 Nm, peak torque 119 Nm, speed 6,000 rpm. It is made by Delta Electronics, Inc.; Specify Motion can help source it or propose an equivalent.
Who makes the Delta Electronics ECM-B3 servo motors?
The Delta Electronics ECM-B3 servo motors is made by Delta Electronics (Delta Electronics, Inc.) and is listed here for engineers comparing options. Specify Motion is not affiliated with Delta Electronics, Inc.; brand names are used only to identify the product.
What is the rated torque of the Delta Electronics ECM-B3 servo motors?
The published series minimum rated torque is 0.32 Nm. Individual models and sizes in the ECM-B3 servo motors range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Delta Electronics ECM-B3 servo motors?
Yes. On published figures, Kinco SMK Series AC Servo Motors (SMK40S/60S/80S, SMK130G, SMK180G) and Kinco SMH Series AC Servo Motors (SMH40S-SMH180D) are the closest match from our supply network. An engineer confirms the fit against your application before recommending anything.
What is the inertia ratio in servo sizing?
The inertia ratio compares the load inertia reflected to the motor shaft with the motor's rotor inertia. High ratios make the axis harder to tune and slower to settle. Many engineers aim for below about 10:1, and lower for highly dynamic axes, using a gearbox to reduce reflected inertia where needed.
Do AC servo motors need an absolute encoder?
Not always. Incremental encoders need a homing routine after power-up, which is acceptable on many machines. Absolute encoders know their position at power-on, avoiding homing, which saves time and suits robots and multi-axis machines. Multi-turn absolute encoders track turns even when power is off.
Further reading: How to select a servo motor · Servo vs stepper · Servo and stepper motors
Other ac servo motor series
Spec builder
Specify what you need instead of ECM-B3 servo motors
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Delta Electronics ECM-B3 servo motors: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.